Improvement of refractory life and performance

Improve your Refractory Life and Performance by following 3 steps

Nothing counts like the 'performance'. Getting or giving a better performance is one thing which everyone tries to do. Reasons obvious! For getting better performance of refractories from an installation (lining) i.e. an improved refractory life, one must take care of the following three simple but very important things:

1. Proper Selection of Refractories.
2. Proper Installation - Laying of Refractory Bricks.
3. Proper Operation Practice.

Selection of Refractories

Though there are specific refractories for different applications, operation practices lead to certain criteria on which, depends the refractory life. As such these need to be properly considered. Customers should disclose the actual operating practices and conditions so that some important properties, required to such conditions can be taken care during the selection of refractories as well as during the manufacturing stage of such refractory bricks, castables, and mortars. Among various physical, chemical, thermo-chemical and thermo-mechanical properties of Refractories, there are a few properties which can change significantly performance of refractories. These are called Key Properties. For ensuring better performance, quality and of course, refractory life these key properties should be tested.

Installation - Laying of Refractory Bricks

Depending on the method of application or installation there has to be a set of guidelines in respect to laying of refractory bricks, their dimensions, selection of mortars, expansion joints and many other minute but very important things. So from case to case basis the supplier of refractories should specify this properly and also ensure that the methods are actually being followed. Transportation, handling, timely arrival of refractory bricks, mortars, skill of masonry work, proper equipment for application e.g. mixer machine for castable, vibrator for installation, forma etc. are very important. Maintaining proper expansion gaps, correct dimension (size) of bricks and monolithics, fixing anchors etc. all are very important to achieve better life of refractories. Once the laying job and other installation of refractories are over, the initial heating of the lining before starting the actual operation is of prime importance. Customers should demand the initial heating schedule from the refractory supplier.

Operational Practices

Proper operation is not only important for getting right quality output but also, help in getting the optimum refractory life, less downtime, maximum availability of the furnace and thus, the benefit of lower cost of refractories per tone of finished product. Customers must be aware of the reasons which can damage the refractories arising because of improper operations. During the training of the furnace operators, apart from the method of the furnace operation etc. they must be given some knowledge regarding the proper usage and importance of refractories also.

how to minimize/stop the erosion in high alumina bottom pouring sets, without much cost increase.

One can try magnesia - carbon refractory coating over the high alumina bottom pouring sets. The coating can be applied using carbonaceous adhesives.

Using BP set manufactured by small companies then probable cause of this erosion can be lower alumina content than specified or using a low melting clay as binder to reduce firing temperature. Total alumina can be checked by sending sample to any reputed lab for chemical testing. However for checking low melting matrix, you have to test hot MOR or RUL property of the sample. In case of low melting matrix, it will fuse at steel temperature and will not hold the grains, so more erosion. So buy only from manufacturers who have high temperature kilns to make fire proper grade of BP sets.

 Reduced oxygen content in the steel will be better for the refractories. I recall a case where the customer "killed" the steel in the ladle with some aluminum prior to casting. It is costly to measure oxygen but will give good information if you can do this.

what's the difference between fused zirconia and chemical grade zirconia,

The term fused zirconia refers to the zirconia grains which are melted by heating above their melting point therefore the surface of these grains is in a fused state and it is nearly theoretically dense. One would expect better thermo mechanical properties from fused grains. Where as chemical grade is generally refered to zirconia prepared by chemical precipitation or decomposition of zirconium salts and such grains show high surface porosity hence they are prone to liquid metal wetting.


 Refractoriness is all about purity. A fused grade will contain fewer of the glass forming impurities which reduce the refractoriness of high melting point materials like zirconia. Hence you will have cleaner grain boundaries less prone to chemical attack, high temperature creep etc. In extreme applications, go for fused grade every time. Of course there are grades of fused materials as well, so you have to go by the quantities and types of impurities present in the chemical analysis to be sure that you're getting a quality product.


Price wise:
It can expected the fused grade to be more expensive. But there are different grades of fused zirconia, as with any other fused material. The fused material obtained from the centre of the melted mass is expected to contain the least contaminants and companies will often sell this material at the highest price whilst sell the material obtained from the outside of the melt at a lower price.
Whether it's better depends upon what use of it and how essential the place it is. That is, it could be cost effective to use the lower grade of zirconia in certain applications. Usually any containment vessel is zoned and the highest grade, fused materials only used in the high wear areas.


Crystal Size :
Cristal size is a major difference. Fused ZrO2 is slowly cooled, thus allowing for better formed and larger crystals than chemical ZrO2.


Lattice Size: 
There can not be major difference in the lattice parameters of the fused and chemical grade calcined zirconia but it may vary by from 5to 6% because the chemical grade is expected to have high vacancy or interstitial concentration hence it may show larger lattice parameter.Since in the fused zirconia the imputities are segregated to the surface of grains during solidification therefore it show lattice corresponding to that of pure zirconia crystal.

how Manganese cause Magcarbon refractory erosion?

1) Rich MnO slags can lead to Mn-rich metallic particles and solid solution with Mg (and, indeed, carbon oxydation) at the interface between slag and lining. 
Anyway, this is seldom the first cause of erosion: it generally occurs after the lining has been weared for some other reason (i.e. slags unsaturated in MgO or rich in FeO).


2) Mn presence in converter causes erosion faster, as it behaves acidic, makes the liquid less viscous, penetrates the pores and joints and reacts with MgO at the contact point. For Mn steel, different of configuration of MgC brick is used.


3) it is observed that after a low grade ore(high impurity i.e Mn,Si) converter life is almost reduced and high erosion profile is being observed. 
as my observation high Mn slag is very fluid and do not cover the converter lining after slag splashing. reducing use of iron ore as coolant may help.


MnO + SiO2 = very low melting and corrosive liquid. 

I suppose primary wear area limiiting converter life will be the trunnions. Trunnions can be zoned with higher quality MgO containing bricks - MgO purity should be 97.5 minimum and of largest MgO crystal size available. Graphite should be 10-20% and have coarse flaked quality -- exact amount of graphite is function of sracp charge; hot metal chemistry; gunning practice; slag viscosity etc. A good start would be 15% C. Metal additions should be aluminum and silicon metal which will form carbides for added strength and corrosion resistance. 

Turkish fused MgO is superior to Chinese fused MgO especially for corrision resistance - crystal size is larger and grain chemistry is more homogeneous. 

Some other thoughts: 

The operator should be adding enough lime/limestone/dolomitic lime to maintain slag basciity at a > 3:1 lime:silca ratio and some MgO is helpful to reduce slag liquidity and reactability. 

Reblows will be especialy harmful as added FeO can result and FeO+MnO+SiO2 is a refractory solvent that is very aggressive. So effort should be taken to control reblowing to minimum. 

Overblowing such that temperature is overheated should be controlled. 

Corriosive slag should be slagged off shortly after tap. 

A high purity MgO gun mix and laser readings to identify low spots for added gunning maintenance will extend service life. 

Do practice slag splashing; a special lance is used to inject nitrogen after tap - the slag is made more refractory prior to the nitrogen splasing by addition of dolomitic lime. 

A good strategy would be to plan for Continuous Improvement over several linings rather than thinking that one design change can be a silver bullet. Key is to study the wear profile, identify the wear mechanism and develop new lining design that addresses the wear area and wear meachanism; this should be repeated in several iterations over several linings as in "chaisng the hole". As one area is upgraded the weak link might move to another area of the vessel. EX: An upgrade of trunnions might shift the limiting zone to the cone or the slagline or the charge pad or the tap pad...

phenomenon of Alumina pick up by the liquid mould flux during Continuous Casting and how it affects the quality of cast strands?

The pickup of alumina in the mold causes the formation of calcium aluminates. Since there are a variety of different calcium aluminate morphs(each one with a higher melting temp.) over time the mold flux can and will begin to thicken up and the fluid lubrication on the strand mold faces can be interrupted causing surface defects & breakouts. Old timers used to throw Calcium flourides (spar) into the mold to liquify it but each time you do that you also increase the CA content which in turn will eventually thicken back up. Spar is a bad actor in the mold. In order to stay fluid there is a delicate chemical balance between CA & Al.

Benefits of using Steel Fibers and Organic Fibers in Refractory Castables and Monolithics

One of the most effective ways of improving the mechanical and thermal properties of refractory castables and other monolithic refractories is adding in suitable proportions of stainless steel fibers and organic fibers to the castable respectively.

Steel Fibers

Steel fiber reinforced refractory castables are very resistant to the tendency of the material to fall apart on thermal cycling. Stainless steel fibers greatly improve the flexural strength of the castable. And this added increase in ductility contributes significantly to the thermal shock and spalling resistance of the material. The fibers generally used are in size varying between 0.1 to 0.4 mm2 in cross-section & 20-40 mm in length. For monolithic SS is used either high chrome or high chrome nickel steels available in the market with different grades. One reason commonly reported that the thermal shock resistance of castables is greatly increased through addition of SS fibers because these fibers act as crack arresters, preventing cracks propagating. This is also possible that the microcracks caused by a mismatch in thermal expansion coefficients of matrix and fibers dissipate energy from larger cracks propagating as a result of thermal stress. However percentage of these fibers added becomes important because of two reasons as it has a direct impact on the fluidity of the castable, then it may also cause mixing difficult due to fiber-balling when added beyond 3% by volume. Another critical factor will be the maximum application temperature for the castable that those fibers present in the castable can resist oxidation (since these fibers can not perform beyond their melting temperature).

Organic Fibers

An effective means for improving the explosive spalling resistance of a castable is to add organic fibers to the formulation. It has been reported that the composition & concentration of fibers are not as important as melting temperature of the fiber, since these fibers after melting increase permeability at certain temp. & thereby reducing the explosive spalling tendency of the castables. The fibers generally used for this purpose are Polypropylene fibers, Polyester staple fibers, etc.
Because of these different advantages it have been found that both organic and SS fiber reinforced refractory castables provide substantial increase in service life and therefore, a considerable reduction in refractory maintenance cost and furnace down-time.

Functions and Importance of Tundish in Continuous Casting - I

The role of tundish in the continuous casting process evolved from that of a buffer between the ladle and mould to being a grade separator and also a device for removing unwanted inclusions through metallurgical processes / chemical reactions. The tundish is intended to deliver the molten metal to the moulds evenly and at a designed throughput rate and temperature without causing contamination by inclusions. It distributes molten steel in continuous casting moulds and is typically operated at a constant bath depth to ensure a constant feed rate into the mould required to achieve a constant throughput. In the sequence of continuous casting, tundish directly control the molten steel in the last stage of liquid steel processing and the refractories used here are therefore, required to have high stability and special properties. Tundish is one of the most important areas of Refractory Application and so, is also one of the biggest ‘cost control center’ in the continuous casting process.

Tundish Refractory Lining


After Bricked Lining and then Gunnable Lining, Tundish Boards (or Board Lining) came into existence as working lining. Silica boards are used for MS grade and MgO boards for SS grade and for high Ca ppm steel. The reason being silica is attacked by lime, alumina and iron oxide present in the steel.


However, for longer duration casting Sprayable Lining such as MgO spray mass (Magnesite spray mass) are widely used with MgO content varying from 70 - 90% and minimum silica content. For example, for 10-12 hrs casting, 70-75% MgO with silica content below 15% are working well. But to achieve 20-25 hrs life, 90% MgO with silica content less than 10% with 35-40 mm thickness at wall and 50-60 mm thickness at the bottom are required. Separate preheating arrangement is required to form the chemical bonding in spray mass after application at around 1000°C.


Of late, tundish spray mass has gradually been replaced by Dry Vibro mass to further elongate the casting sequence. MgO content varies from 70-90% with low silica content to achieve a sequence length of 12-15 hrs to 35-40 hrs. One advantage of Dry Vibro mass is that it ensures low hydrogen pick up in steel as it does not require water for application. Approximately 0.7-0.9 ppm hydrogen pick up is reported as compared to 1.8-2.4 ppm in spray mass. Special drying arrangement is required for drying this mass at around 300°C for 24 hrs to develop polymerisation of resin which gives strength to it.

applicability of fused MgO (periclase) with a grain size from 0.5 to 0.001 and the content of the MgO is not more than 95%

 1) In finer fraction of batch composition of magnesia carbon bricks for ladle free board and EAF slag door application.

2) Some quantity can be mixed with coarser grains of DBM 95 to produce wet ramming mass.

3) Can be mixed with DBM ,graphite and a binder to produce slag conditioner balls for using in converter,LF,etc.